Smart Line Modules

Заказные данные
(9)
Аксессуары
(1)

Smart Line Modules are infeed/regenerative feedback units that supply power to connected Motor Modules. Furthermore, they are capable of feeding regenerative energy back into the grid. The infeed occurs over a diode jumper, while stable, line-commutated regenerative feedback takes place via IGBTs with 100 % continuous energy regeneration. The regenerative capability of the modules can be deactivated by means of parameterization.

Smart Line Modules are designed for connection to grounded TN/TT and non-grounded IT supply systems.

The DC link is pre-charged by means of integrated pre-charging resistors.

To operate the Smart Line Module, the associated line reactor or a suitable transformer is required.

Дизайн

The Smart Line Modules have the following interfaces as standard:

1 line supply connection
1 connection for the 24 V DC electronics power supply
1 DC link connection (DCP, DCN) for supplying the connected Motor Modules
1 DC link connection (DCPA, DCNA) for connecting a Braking Module
3 DRIVE-CLiQ sockets
1 temperature sensor input for KTY84‑130, Pt1000, PTC or Pt100 (Pt1000 can be used from firmware V4.7 HF17)
1 PE/protective conductor connection (2 connections for sizes HX and JX)

The status of the Smart Line Modules is indicated via three LEDs.

The scope of supply of the Smart Line Modules includes:

DRIVE-CLiQ cable to connect to a Control Unit
DRIVE-CLiQ cable for connection between the Control Unit and first Motor Module (type dependent)
1 set of warning labels in 30 languages
(BG, CN, CZ, DE, DK, EE, ES, FI, FR, GB, GR, HU, IE, IS, IT, JP, KR, LT, LV, MT, NL, NO, PL, PT, RO, RU, SE, SI, SK, TR)

Интеграция

The Smart Line Modules communicate with the higher-level control module via DRIVE-CLiQ. The control module in this case can be a CU320-2 or a SIMOTION D Control Unit. An external 24 V DC power supply is required to operate the Smart Line Modules.

Connection example of a Smart Line Module

Технические данные

General technical specifications

Electrical specifications
Line power factor at rated power
Basic fundamental (cos φ₁)	>0.96
Total (λ)	0.75 ... 0.93
Efficiency	>98.5 %
DC link voltage, approx. ¹⁾	1.32 × line voltage under partial load 1.30 × line voltage under full load
Main contactor control
Terminal block -X9/5-6	240 V AC, max. 8 A 30 V DC, max. 1 A

¹⁾ The DC link voltage is unregulated and load-dependent. For additional information, please refer to the SINAMICS Low Voltage Engineering Manual.

Line voltage 380 ... 480 V 3 AC		Smart Line Modules
		6SL3330-6TE35-5AA3	6SL3330-6TE37-3AA3	6SL3330-6TE41-1AA3	6SL3330-6TE41-3AA3	6SL3330-6TE41-7AA3
Rated power
At I_rated DC (50 Hz 400 V)	kW	250	355	500	630	800
At I_H DC (50 Hz 400 V)	kW	235	315	450	555	730
At I_rated DC (60 Hz 460 V)	hp	385	545	770	970	1230
At I_H DC (60 Hz 460 V)	hp	360	485	695	855	1125
DC link current
Rated current I_rated DC	A	550	730	1050	1300	1700
Base-load current I_H DC¹⁾	A	490	650	934	1157	1513
Maximum current I_max DC	A	825	1095	1575	1950	2550
Infeed/regenerative feedback current
Rated current I_rated I	A	463	614	883	1093	1430
Maximum current I_max I	A	694	921	1324	1639	2145
Current demand
24 V DC auxiliary power supply	A	1.35	1.35	1.4	1.5	1.7
400 V AC	A	1.8	1.8	3.6	5.4	5.4
DC link capacitance
Smart Line Module	μF	8400	12000	16800	18900	28800
Drive line-up, max.	μF	42000	60000	67200	75600	115200
Power loss, max. ²⁾
At 50 Hz 400 V	kW	3.7	4.7	7.1	11.0	11.5
At 60 Hz 460 V	kW	3.7	4.7	7.1	11.0	11.5
Cooling air requirement	m³/s (ft³/s)	0.36 (12.7)	0.36 (12.7)	0.78 (27.5)	1.08 (38.1)	1.08 (38.1)
Sound pressure level L_pA (1 m) at 50/60 Hz	dB	69/73	69/73	70/73	70/73	70/73
Line connection U1, V1, W1		Flat connector for M10 screw	Flat connector for M10 screw	Flat connector for M12 screw	Flat connector for M12 screw	Flat connector for M12 screw
Conductor cross section, max. (IEC)	mm²	2 × 240	2 × 240	4 × 240	6 × 240	6 × 240
DC link connection DCP, DCN		M10 screw	M10 screw	4 × hole for M12	4 × hole for M12	4 × hole for M12
Conductor cross section, max. (IEC)	mm²	2 × 240	2 × 240	Busbar	Busbar	Busbar
PE/GND connection		Hole for M10	Hole for M10	–	–	–
Conductor cross section, max. (IEC)	mm²	2 × 240	2 × 240	–	–	–
PE1/GND connection		–	–	M12 screw	M12 screw	M12 screw
Conductor cross section, max. (IEC)	mm²	–	–	240	240	240
PE2/GND connection		–	–	2 × M12 screw	2 × M12 screw	2 × M12 screw
Conductor cross section, max. (IEC)	mm²	–	–	2 × 240	2 × 240	2 × 240
Cable length, max. ³⁾
Shielded	m (ft)	4000 (13124)	4000 (13124)	4800 (15749)	4800 (15749)	4800 (15749)
Unshielded	m (ft)	6000 (19686)	6000 (19686)	7200 (23623)	7200 (23623)	7200 (23623)
Degree of protection		IP00	IP00	IP00	IP00	IP00
Dimensions
Width	mm (in)	310 (12.2)	310 (12.2)	503 (19.8)	704 (27.7)	704 (27.7)
Height	mm (in)	1413 (55.6)	1413 (55.6)	1475 (58.1)	1480 (58.3)	1480 (58.3)
Depth	mm (in)	550 (21.6)	550 (21.6)	548 (21.6)	550 (21.6)	550 (21.6)
Weight, approx.	kg (lb)	150 (331)	150 (331)	294 (648)	458 (1010)	458 (1010)
Frame size		GX	GX	HX	JX	JX
Minimum short-circuit current⁴⁾	A	6200	9200	10400	16000	21000

¹⁾ The base-load current I_{H DC} is the basis for a duty cycle of 150 % for 60 s or I_{max DC} for 5 s with a duty cycle duration of 300 s.

²⁾ The specified power loss represents the maximum value at 100% utilization. The value is lower under normal operating conditions.

³⁾ Total of all motor cables and DC link. Longer cable lengths for specific configurations are available on request. For additional information, please refer to the SINAMICS Low Voltage Engineering Manual.

⁴⁾ Current required for reliably triggering protective devices.

Line voltage 500 ... 690 V 3 AC		Smart Line Modules
		6SL3330-6TG35-5AA3	6SL3330-6TG38-8AA3	6SL3330-6TG41-2AA3	6SL3330-6TG41-7AA3
Rated power
At I_rated DC (50 Hz 690 V)	kW	450	710	1000	1400
At I_H DC (50 Hz 690 V)	kW	405	665	885	1255
At I_rated DC (50 Hz 500 V)	kW	320	525	705	995
At I_H DC (50 Hz 500 V)	kW	295	480	640	910
At I_rated DC (60 Hz 575 V)	hp	500	790	1115	1465
At I_H DC (60 Hz 575 V)	hp	450	740	990	1400
DC link current
Rated current I_rated DC	A	550	900	1200	1700
Base-load current I_H DC¹⁾	A	490	800	1068	1513
Maximum current I_max DC	A	825	1350	1800	2550
Infeed/regenerative feedback current
Rated current I_rated I	A	463	757	1009	1430
Maximum current I_max I	A	694	1135	1513	2145
Current demand
24 V DC auxiliary power supply	A	1.35	1.4	1.5	1.7
500 V AC	A	1.3	2.9	4.3	4.3
690 V AC	A	0.94	2.1	3.1	3.1
DC link capacitance
Smart Line Module	μF	5600	7400	11100	14400
Drive line-up, max.	μF	28000	29600	44400	57600
Power loss, max. ²⁾
At 50 Hz 690 V	kW	4.3	6.5	12.0	13.8
At 60 Hz 575 V	kW	4.3	6.5	12.0	13.8
Cooling air requirement	m³/s (ft³/s)	0.36 (12.7)	0.78 (27.5)	1.08 (38.1)	1.08 (38.1)
Sound pressure level L_pA (1 m) at 50/60 Hz	dB	69/73	70/73	70/73	70/73
Line connection U1, V1, W1		Flat connector for M10 screw	Flat connector for M12 screw	Flat connector for M12 screw	Flat connector for M12 screw
Conductor cross section, max. (IEC)	mm²	2 × 240	4 × 240	6 × 240	6 × 240
DC link connection DCP, DCN		M10 screw	4 × hole for M12	4 × hole for M12	4 × hole for M12
Conductor cross section, max. (IEC)	mm²	2 × 240	Busbar	Busbar	Busbar
PE connection		Hole for M10	–	–	–
Conductor cross section, max. (IEC)	mm²	2 × 240	–	–	–
PE1/GND connection		–	M12 screw	M12 screw	M12 screw
Conductor cross section, max. (IEC)	mm²	–	240	240	240
PE2/GND connection		–	2 × M12 screw	2 × M12 screw	2 × M12 screw
Conductor cross section, max. (IEC)	mm²	–	2 × 240	2 × 240	2 × 240
Cable length, max. ³⁾
Shielded	m (ft)	2250 (7382)	2750 (9023)	2750 (9023)	2750 (9023)
Unshielded	m (ft)	3375 (11073)	4125 (13534)	4125 (13534)	4125 (13534)
Degree of protection		IP00	IP00	IP00	IP00
Dimensions
Width	mm (in)	310 (12.2)	503 (19.8)	704 (27.7)	704 (27.7)
Height	mm (in)	1413 (55.6)	1475 (58.1)	1480 (58.3)	1480 (58.3)
Depth	mm (in)	550 (21.6)	548 (21.6)	550 (21.6)	550 (21.6)
Weight, approx.	kg (lb)	150 (331)	294 (648)	458 (1010)	458 (1010)
Frame size		GX	HX	JX	JX
Minimum short-circuit current⁴⁾	A	6200	10500	12400	21000