SIMATIC IFP1900 INOX PRO

• Заказные данные
  (2)
• Информационные материалы

  Информационные материалы

  SIMATIC IFP1900 INOX PRO

  Industrial Flat Panel in fully enclosed stainless steel housing with high degree of protection for operation and visualization close to machines in the food and beverage, pharmaceutical and fine chemicals industries and in other areas where hygienic requirements are high.

  The device has been developed on the basis of EN 1672-2 "Food processing machinery – Safety and hygiene requirements".

  With its fully protected design and optional expansion modules, the SIMATIC PRO devices are are eminently suitable for industrial and machine-level use.

  The INOX PRO devices with their stainless steel housing are compact and hygienically designed and feature integrated operating elements. They are also even better equipped to meet the high requirements presented by the food and beverage production environment. IP66K degree of protection protects against water even with a jet strength of 100 l/min at 10 bar from a distance of 2.5 m to 3 m.

  The optimized profile and minimal housing depth allow liquids to run off.

  The high quality requirements in the food and beverages industry require a high standard of the food processing machinery. There are many relevant regulations, directives, ordinances, standards and laws. Essential here is that all equipment and components are easy to clean and disinfect so that cross-contamination of foodstuffs can be avoided.

  Область применения

  • Food production
  • Slaughterhouse
  • Secondary packaging/cartoning, filling
  • Primary packaging
  • Pharmaceutical and cosmetics industry
  • Chemical industry
  • Life sciences

  Дизайн

  • TFT widescreen display
  • Analog-resistive touch screen sensor
  • Stainless steel surface ground with 240 grit hairline finish
  • Device developed on the basis of DIN EN 1672-2
  • Resistant, decorative membrane tested against chemicals in accordance with DIN 42115, Part 2
  • Food-standard flat seal in accordance with FDA 21 CFR 177.2006
  • Housing material:
    Stainless steel, material number 1.4301
  • Food-standard sealing material:
    FPM (fluoroelastomer)
  • Continuous front membrane:
  • Degree of protection: IP66K all-round
  • Front operator controls:
    2 illuminated pushbuttons with LEDs, 1 EMERGENCY OFF pushbutton, wired to terminal strip
  • Mechanical interface:
    For pedestal or support-arm mounting
  • Service cover for access to the interfaces, cable routing through the support system

  Особенности

  • Proven hygienic design for easy cleaning and disinfection
  • High all-round IP66K degree of protection for increased tightness and ruggedness
  • Food-standard sealing material and shatter protection for the display to prevent contamination of foodstuffs
  • Flat, optimized hygienic design allows liquids to run off
  • Same functionality as the comparable standard product
  • Small footprint thanks to compact, enclosed design
  • Pre-installed operating elements
  • Flexible implementation due to optional pedestal or support-arm mounting
  • Quick access to interfaces by means of the removable connection cover
  • Flange adapter for tube with 40 mm inside diameter permits connection to a wide range of accessories

  Технические данные

  IFP1900 INOX PRO
  Special features	Pedestal mounting	Support arm mounting
  General features
  Display	18.5" TFT widescreen display
  Resolution (pixels)	1 366 x 768
  MTBF of backlit display (at 25°C)	50,000 h
  Power supply	24 V DC
  Equipment
  Touch	Analog-resistive touch (single touch)
  Control elements	2 x illuminated pushbutton with LED (red, green), 1 x emergency off; permanently wired on terminals
  Option	External, USB interface on rear with captive stainless steel lock
  Special features	Flange adapter for pedestal	Flange adapter for support arm
  Configuration / interfaces
  	Based on SIMATIC IFP1900 (6AV7863-3MA20-0AA0)
  	1 x DisplayPort interface
  	1 x Ethernet interface (RJ45) up to 1 Mbit/s
  	2 x USB interface
  	For connecting to an IPC427D with these system requirements: Configuration 1:1, without multi-monitor mode RAM min. 2 GB Operating systems Windows 7, WES7 Ethernet with min. 100 Mbit/s
  Enclosure
  Front	Stainless steel 1.4301, polyester-based membrane
  Material	Stainless steel 1.4301
  Surface	Hairline finish, 240 grit abrasive grain
  Device seals	FPM, molded parts, replaceable
  Special features	Decorative display membrane; without USB port on front
  Ambient conditions
  Degree of protection, complete	IP66K, enclosure type 4 and 4x (indoor use only)
  Ambient temperature during operation	0 ... +45 °C
  Relative humidity during operation	Max. 95 %, no condensation
  Transport temperature / storage temperature / humidity	- 20°C … + 60°C / 10 % to 90 % without condensation
  Approvals and inspections	CE; hygiene testing according to EN 1672-2
  Approvals (planned)	RCM (previously C-Tick)/KC/CUL
  Sector	Food & beverages, pharmaceuticals industry, cosmetics industry, fine chemicals, other hygiene areas
  Dimensions
  External dimensions (W x H x D in mm)	544 x 430.7 x 136	544 x 430.7 x 136
  Depth of enclosure only (without flange and operator controls) in mm	80	80
  Weight, net	15.5 kg	15.5 kg
  Special features	Flange adapter for pedestal	Flange adapter for support arm
  The other specifications correspond to the basic unit (MLFB)	SIMATIC IFP1900 (6AV7863-3MA20-0AA0)

  
  
  

  Дальнейшая информация

  Additional information is available on the Internet at:

  http://www.siemens.com/inox-pro-hmi-devices

  For other languages:

  http://www.siemens.com/inox-pro-hmi-devices

  Customer-specific modifications

  • Customized design (logo, type designation and membrane color)
  • Other display sizes
  • Changes to the operator controls
  • Further certificates and approvals

  Quotation preparation

  Customized automation specialists define the product modifications precisely in accordance with customer requirements.

  The quotation is then prepared with:

  • Non-recurring costs,
  • Prototype costs,
  • Serial device prices and
  • the general conditions in the form of a product agreement (e.g. minimum quantity).

  The defined device can then be ordered easily using this product agreement and a customer-specific order number.