SIPLUS extreme RAIL digital output modules

Заказные данные
(2)

8 and 16-channel digital output modules
Approved in accordance with the railway standards EN 50155, EN 15121, EN 50124, EN 50125 and EN 45545 for use in rail traffic
For flexible adaptation of the controller to the corresponding task
For subsequent expansion of the system with additional outputs

Область применения

Digital output modules switch 24 V DC or 230 V AC voltages in the plant and thus transfer internal signals from the controller to the plant. Solenoid valves, DC contactors, and indicator lights can be connected.

The output modules have settable parameters and diagnostic functions and can thus be adapted flexibly to the respective process requirements.

Дизайн

Installation on the S7-1500 mounting rail using one single screw
Standardized 40-pin front connector using screw terminal or push-in technology
Standardized, harmonized front connector assignment for easier wiring
Connectable core cross-sections: 0.25 mm² to 1.5 mm² (AWG24 to 16)
Integrated potential bridges for flexible creation of potential groups
Front connector can be set to prewiring position
Front flap with expandable cable compartment, even if fully wired
Unambiguous labeling on front of module:
- Module type
- Article No.
- Hardware and firmware version
- Channel numbers labeling
- Cabling diagram

Included in the scope of delivery:

One labeling strip for manual labeling
One U connector
Printed front door

Функции

Uniform display and diagnostics concept:
- Module status display for ERROR (red LED) and RUN (green LED)
- Channel status indicator for signal state log. “0” and log. "1" (green LED) or indication of short-circuit (red LED)
- Display for monitoring the 24 V DC supply voltage (green LED)
Supported functions:
- Identification and maintenance data IM0 to IM3
- Firmware update
- Channel-granular parameter assignment (HF modules only)
- Channel-granular diagnostics (HF modules only)
- Isochronous mode (dependent on the module)
- Substitute values can be parameterized for the outputs

Технические данные

Order number	6AG2522-1BH01-4AB0	6AG2522-5HF00-1AB0
	SIPLUS S7-1500 DQ 16x24VDC HF TX RAIL	SIPLUS S7-1500 DQ 8x230VAC ST 5A T1 RAIL
General information
Product type designation	DQ 16x24VDC/0.5A HF	DQ 8x230 V AC/5 A ST (relay)
Product function
● I&M data	Yes; I&M0 to I&M3	Yes; I&M0 to I&M3
Operating mode
● MSO	Yes
Supply voltage
Type of supply voltage	DC	DC
Rated value (DC)	24 V	24 V
Reverse polarity protection	Yes; through internal protection with 7 A per group
Digital outputs
Type of digital output	Transistor	Relays
Number of digital outputs	16	8
Current-sourcing	Yes
Digital outputs, parameterizable	Yes	Yes
Short-circuit protection	Yes; Clocked electronically
Open-circuit detection	Yes
Limitation of inductive shutdown voltage to	L+ (-53 V)
Controlling a digital input	Yes	possible
Switching capacity of the outputs
● with resistive load, max.	0.5 A
● on lamp load, max.	5 W	1 500 W; 10 000 operating cycles
● Low energy/fluorescent lamps with electronic control gear		10x 58 W (25 000 operating cycles)
● Fluorescent tubes, conventionally compensated		1x 58 W (25 000 operating cycles)
● Fluorescent tubes, uncompensated		10x 58 W (25 000 operating cycles)
Load resistance range
● lower limit	48 Ω
● upper limit	12 kΩ
Output voltage
● Type of output voltage	DC
● for signal "1", min.	L+ (-0.8 V)
Output current
● for signal "1" rated value	0.5 A	5 A
● for signal "0" residual current, max.	0.5 mA	0 A
Output delay with resistive load
● "0" to "1", max.	100 µs
● "1" to "0", max.	100 µs; at rated load
Parallel switching of two outputs
● for logic links	Yes	Yes
● for uprating	Yes	No
● for redundant control of a load	Yes	Yes
Switching frequency
● with resistive load, max.	100 Hz	2 Hz
● with inductive load, max.	0.5 Hz; According to IEC 60947-5-1, DC-13	0.5 Hz
● on lamp load, max.	10 Hz	2 Hz
Total current of the outputs
● Current per channel, max.	0.5 A; see additional description in the manual	8 A; see additional description in the manual
● Current per group, max.	4 A; see additional description in the manual	8 A; see additional description in the manual
● Current per module, max.	8 A; see additional description in the manual	64 A; see additional description in the manual
Relay outputs
● Number of relay outputs		8
● Rated supply voltage of relay coil L+ (DC)		24 V
● Current consumption of relays (coil current of all relays), max.		80 mA
● external protection for relay outputs		With miniature circuit breaker with characteristic B for: cos φ 1.0: 600 A cos φ 0.5 ... 0.7: 900 A with 8 A Diazed fuse: 1000 A
● Contact connection (internal)		No
● Size of motor starters according to NEMA, max.		5
● Number of operating cycles, max.		4 000 000; see additional description in the manual
● Relay approved acc. to UL 508		Yes; 250 V AC/5 A g.p.; 120 V AC TV-4 tungsten; A300, R300
Switching capacity of contacts
— with inductive load, max.		see additional description in the manual
— with resistive load, max.		see additional description in the manual
Cable length
● shielded, max.	1 000 m	1 000 m
● unshielded, max.	600 m	600 m
Isochronous mode
Isochronous operation (application synchronized up to terminal)	Yes	No
Execution and activation time (TCO), min.	70 µs
Bus cycle time (TDP), min.	250 µs
Interrupts/diagnostics/status information
Diagnostics function	Yes	Yes
Substitute values connectable	Yes	Yes
Alarms
● Diagnostic alarm	Yes	Yes
Diagnostic messages
● Monitoring the supply voltage	Yes	Yes
● Wire-break	Yes	No
● Short-circuit	Yes	No
● Fuse blown	No
Diagnostics indication LED
● RUN LED	Yes; Green LED	Yes; Green LED
● ERROR LED	Yes; Red LED	Yes; Red LED
● Monitoring of the supply voltage (PWR-LED)	Yes; Green LED	Yes; Green LED
● Channel status display	Yes; Green LED	Yes; Green LED
● for channel diagnostics	Yes; Red LED	No
● for module diagnostics	Yes; Red LED	Yes; Red LED
Potential separation
Potential separation channels
● between the channels and backplane bus	Yes	Yes
Isolation
Isolation tested with	707 V DC (type test) and according to EN 50155 (routine test)	Between the channels: 2 500 V DC; between the channels and backplane bus: 2 500 V DC; between L+ and backplane bus 707 V DC (type test) and according to EN 50155 (routine test)
Standards, approvals, certificates
Suitable for safety functions	No	No
Suitable for safety-oriented group deactivation		No
Railway application
● EN 50121-3-2	Yes; EMC for rail vehicles	Yes; EMC for rail vehicles
● EN 50121-4	Yes; EMC for signal and telecommunications systems	Yes; EMC for signal and telecommunications systems
● EN 50124-1	Yes; Railway applications - overvoltage category OV2; pollution degree PD2; rated surge voltage UNi = 0.5 kV; UNm = 24 V DC	Yes; Railway applications - overvoltage category OV2; pollution degree PD2; rated surge voltage UNi = 0.5 kV; UNm = 24 V DC
● EN 50125-1	Yes; Rail vehicles - see ambient conditions	Yes; Rail vehicles - see ambient conditions
● EN 50125-2	Yes; Stationary electrical equipment - see ambient conditions	Yes; Stationary electrical equipment - see ambient conditions
● EN 50125-3	Yes; Signal and telecommunications systems - see ambient conditions; vibrations and shocks: Application point outside of tracks (1 m to 3 m away from track)	Yes; Signal and telecommunications systems - see ambient conditions; vibrations and shocks: Application point outside of tracks (1 m to 3 m away from track)
● EN 50155	Yes; Rail vehicles - temperature class Tx, horizontal mounting position, salt spray Class ST2	Yes; Rail vehicles - temperature class T1, horizontal mounting position, salt spray Class ST2
● EN 61373	Yes; Rail vehicles - vibrations and shocks: Category 1 Class A/B	Yes; Rail vehicles - vibrations and shocks: Category 1 Class A/B
● Fire protection acc. to EN 45545-2	Yes; Rail vehicles - verification on request	Yes; Rail vehicles - verification on request
Ambient conditions
Ambient temperature during operation
● horizontal installation, min.	-40 °C; = Tmin	-25 °C; = Tmin
● horizontal installation, max.	70 °C; = Tmax; > +60 °C number of simultaneously controllable outputs max. 8x 0.5 A, max. total current per group 2 A; +85 °C for 10 minutes (Tx acc. to EN 50155)	60 °C; = Tmax; +70 °C for 10 min (T1 acc. to EN 50155)
Extended ambient conditions
● relative to ambient temperature-atmospheric pressure-installation altitude	Tmin ... Tmax at 1080 hPa ... 795 hPa (-1000 m ... +2000 m)	Tmin ... Tmax at 1080 hPa ... 795 hPa (-1000 m ... +2000 m)
Relative humidity
— With condensation, tested in accordance with IEC 60068-2-38, max.	100 %; RH incl. condensation/frost (no commissioning under condensation conditions)	100 %; RH incl. condensation/frost (no commissioning under condensation conditions)
Resistance
— against biologically active substances / conformity with EN 60721-3-3	Yes; Class 3B2 mold, fungus and dry rot spores (with the exception of fauna). The supplied connector covers must remain on the unused interfaces during operation!	Yes; Class 3B2 mold, fungus and dry rot spores (with the exception of fauna). The supplied connector covers must remain on the unused interfaces during operation!
— against biologically active substances/conformity with EN 60721-3-5	Yes; Class 5B2 mold and fungal spores (excluding fauna). The supplied plug covers must remain in place over the unused interfaces during operation!	Yes; Class 5B2 mold and fungal spores (excluding fauna). The supplied plug covers must remain in place over the unused interfaces during operation!
— against chemically active substances / conformity with EN 60721-3-3	Yes; Class 3C4 (RH < 75%) incl. salt spray according to EN 60068-2-52 (degree of severity 3). The supplied connector covers must remain on the unused interfaces during operation!	Yes; Class 3C4 (RH < 75%) incl. salt spray according to EN 60068-2-52 (degree of severity 3). The supplied connector covers must remain on the unused interfaces during operation!
— against chemically active substances/conformity with EN 60721-3-5	Yes; Class 5C3 (RH < 75%) including salt spray according to EN 50155 (ST2). The supplied plug covers must remain in place over the unused interfaces during operation!	Yes; Class 5C3 (RH < 75%) including salt spray according to EN 50155 (ST2). The supplied plug covers must remain in place over the unused interfaces during operation!
— against mechanically active substances / conformity with EN 60721-3-3	Yes; Class 3S4 incl. sand, dust. The supplied connector covers must remain on the unused interfaces during operation!	Yes; Class 3S4 incl. sand, dust. The supplied connector covers must remain on the unused interfaces during operation!
— against mechanically active substances/conformity with EN 60721-3-5	Yes; Class 5S3 including sand and dust. The supplied plug covers must remain in place over the unused interfaces during operation!	Yes; Class 5S3 including sand and dust. The supplied plug covers must remain in place over the unused interfaces during operation!
Decentralized operation
Fast Startup supported		Yes; 500 ms
Prioritized startup	Yes
Dimensions
Width	35 mm	35 mm
Height	147 mm	147 mm
Depth	129 mm	129 mm
Weights
Weight, approx.	230 g	350 g
Other
Note:	For use in railway applications, also observe the product information "SIPLUS extreme RAIL" A5E37661960A Online Support article 109736776	For use in railway applications, also observe the product information "SIPLUS extreme RAIL" A5E37661960A Online Support article 109736776

SIPLUS extreme RAIL digital output modules

Информационные материалы

Область применения

Дизайн

Функции

Технические данные