SIPLUS extreme RAIL analog input modules

• Заказные данные
  (2)
• Информационные материалы

  Информационные материалы

  • 8-channel analog input modules
  • Approved in accordance with the railway standards EN 50155, EN 15121, EN 50124, EN 50125 and EN 45545 for use in rail traffic.
  • Optionally with extremely short conversion times
  • For the connection of analog sensors without additional amplifiers
  • Even solves more complex automation tasks

  Область применения

  Analog input modules record process signals such as pressure or temperature and forward them in digitalized format (16-bit format) to the control. They are suitable for measuring current (2-wire and 4-wire transducers), voltage, and resistance, as well as for the connection of resistance thermometers and thermocouples (measurement types depend on the module).

  Дизайн

  • Installation on the S7-1500 mounting rail using one single screw
  • Standardized 40-pin front connector using screw terminal or push-in technology
  • Connectable core cross-sections: 0.25 mm² to 1.5 mm² (AWG24 to 16), regardless of the front connector used
  • Front connector can be set to prewiring position
  • Front flap with expandable cable compartment, even if fully wired
  • Integrated shielding concept
  • Unambiguous labeling on front of module:
    • Module type
    • Article No.
    • Hardware and firmware version
    • Channel numbers labeling
    • Cabling diagram

  Included in the scope of delivery:

  • Infeed element, shield clamp, and shield terminal
  • One labeling strip for manual labeling
  • One U connector
  • Printed front door

  Функции

  • Uniform display and diagnostics concept:
    • Module status display for ERROR (red LED) and RUN (green LED)
    • Channel status display (channel activated or deactivated, green LED) or diagnostics display (red LED)
    • Display for monitoring the 24 V DC supply voltage (green LED)
  • Supported functions:
    • Consistently high resolution of 16 bits
    • Identification and maintenance data IM0 to IM3
    • Firmware update
    • Channel-specific parameter assignment
    • Hardware interrupts; two upper and two lower limits can be parameterized
    • Channel-granular diagnostics (depends on measurement type/measuring range)
    • Isochronous mode (dependent on the module)
    • Calibration during runtime

  Технические данные

  Order number		6AG2531-7NF10-1AB0	6AG2531-7KF00-1AB0
  		SIPLUS S7-1500 AI 8xU/I HS T1 RAIL	SIPLUS S7-1500 AI 8xU/I/RTD/TC T1 RAIL
  General information
  Product type designation		AI 8xU/I HS	AI 8xU/I/RTD/TC ST
  Product function
  ● I&M data		Yes; I&M0 to I&M3	Yes; I&M0 to I&M3
  ● Measuring range scalable		No
  Operating mode
  ● Oversampling		No
  ● MSI		Yes
  CiR – Configuration in RUN
  Reparameterization possible in RUN		Yes	Yes
  Calibration possible in RUN		Yes	Yes
  Supply voltage
  Type of supply voltage		DC	DC
  Rated value (DC)		24 V	24 V
  Reverse polarity protection		Yes
  Analog inputs
  Number of analog inputs		8	8
  ● For current measurement		8	8
  ● For voltage measurement		8	8
  ● For resistance/resistance thermometer measurement			4
  ● For thermocouple measurement			8
  permissible input voltage for voltage input (destruction limit), max.		28.8 V	28.8 V
  permissible input current for current input (destruction limit), max.		40 mA	40 mA
  Technical unit for temperature measurement adjustable			Yes
  Input ranges (rated values), voltages
  ● 1 V to 5 V		Yes	Yes
  ● -1 V to +1 V			Yes
  ● -10 V to +10 V		Yes	Yes
  ● -2.5 V to +2.5 V			Yes
  ● -250 mV to +250 mV			Yes
  ● -5 V to +5 V		Yes	Yes
  ● -50 mV to +50 mV			Yes
  ● -500 mV to +500 mV			Yes
  ● -80 mV to +80 mV			Yes
  Input ranges (rated values), currents
  ● 0 to 20 mA		Yes	Yes
  ● -20 mA to +20 mA		Yes	Yes
  ● 4 mA to 20 mA		Yes	Yes
  Input ranges (rated values), thermocouples
  ● Type B			Yes
  ● Type E			Yes
  ● Type J			Yes
  ● Type K			Yes
  ● Type N			Yes
  ● Type R			Yes
  ● Type S			Yes
  ● Type T			Yes
  Input ranges (rated values), resistance thermometer
  ● Ni 100			Yes; Standard/climate
  ● Ni 1000			Yes; Standard/climate
  ● LG-Ni 1000			Yes; Standard/climate
  ● Pt 100			Yes; Standard/climate
  ● Pt 1000			Yes; Standard/climate
  ● Pt 200			Yes; Standard/climate
  ● Pt 500			Yes; Standard/climate
  Input ranges (rated values), resistors
  ● 0 to 150 ohms			Yes
  ● 0 to 300 ohms			Yes
  ● 0 to 600 ohms			Yes
  ● 0 to 6000 ohms			Yes
  ● PTC			Yes
  Thermocouple (TC)
  Temperature compensation
  — parameterizable			Yes
  Cable length
  ● shielded, max.		800 m	800 m; for U/I, 200 m for R/RTD, 50 m for TC
  Analog value generation for the inputs
  Integration and conversion time/resolution per channel
  ● Resolution with overrange (bit including sign), max.		16 bit
  ● Basic execution time of the module (all channels released)		62.5 µs; independent of number of activated channels
  Smoothing of measured values
  ● parameterizable		Yes
  Encoder
  Connection of signal encoders
  ● for voltage measurement		Yes	Yes
  ● for current measurement as 2-wire transducer		Yes	Yes
  — Burden of 2-wire transmitter, max.		820 Ω	820 Ω
  ● for current measurement as 4-wire transducer		Yes	Yes
  ● for resistance measurement with two-wire connection			Yes; Only for PTC
  ● for resistance measurement with three-wire connection			Yes; All measuring ranges except PTC; internal compensation of the cable resistances
  ● for resistance measurement with four-wire connection			Yes; All measuring ranges except PTC
  Errors/accuracies
  Basic error limit (operational limit at 25 °C)
  ● Voltage, relative to input range, (+/-)		0.2 %	0.1 %
  ● Current, relative to input range, (+/-)		0.2 %	0.1 %
  ● Resistance, relative to input range, (+/-)			0.1 %
  ● Resistance thermometer, relative to input range, (+/-)			Ptxxx standard: ±0.7 K, Ptxxx climate: ±0.2 K, Nixxx standard: ±0.3 K, Nixxx climate: ±0.15 K
  ● Thermocouple, relative to input range, (+/-)			Type B: > 600 °C ±1.7 K, type E: > -200 °C ±0.7 K, type J: > -210 °C ±0.8 K, type K: > -200 °C ±1.2 K, type N: > -200 °C ±1.2 K, type R: > 0 °C ±1.9 K, type S: > 0 °C ±1.9 K, type T: > -200 °C ±0.8 K
  Interference voltage suppression for f = n x (f1 +/- 1 %), f1 = interference frequency
  ● Series mode interference (peak value of interference < rated value of input range), min.			40 dB
  ● Common mode voltage, max.		10 V	10 V
  ● Common mode interference, min.		60 dB; at 400 Hz: 50 dB	60 dB
  Isochronous mode
  Isochronous operation (application synchronized up to terminal)		Yes
  Filtering and processing time (TCI), min.		80 µs
  Bus cycle time (TDP), min.		250 µs
  Interrupts/diagnostics/status information
  Diagnostics function		Yes	Yes
  Alarms
  ● Diagnostic alarm		Yes	Yes
  ● Limit value alarm		Yes; two upper and two lower limit values in each case	Yes; two upper and two lower limit values in each case
  Diagnostic messages
  ● Monitoring the supply voltage		Yes	Yes
  ● Wire-break		Yes; only for 1 ... 5 V and 4 ... 20 mA	Yes; Only for 1 to 5 V, 4 to 20 mA, TC, R, and RTD
  ● Overflow/underflow		Yes	Yes
  Diagnostics indication LED
  ● RUN LED			Yes; Green LED
  ● ERROR LED			Yes; Red LED
  ● Monitoring of the supply voltage (PWR-LED)		Yes; Green LED	Yes; Green LED
  ● Channel status display		Yes; Green LED	Yes; Green LED
  ● for channel diagnostics		Yes; Red LED	Yes; Red LED
  ● for module diagnostics		Yes; Red LED	Yes; Red LED
  Potential separation
  Potential separation channels
  ● between the channels and backplane bus		Yes	Yes
  Isolation
  Isolation tested with		707 V DC (type test) and according to EN 50155 (routine test)	707 V DC (type test) and according to EN 50155 (routine test)
  Standards, approvals, certificates
  Railway application
  ● EN 50121-3-2		Yes; EMC for rail vehicles	Yes; EMC for rail vehicles
  ● EN 50121-4		Yes; EMC for signal and telecommunications systems	Yes; EMC for signal and telecommunications systems
  ● EN 50124-1		Yes; Railway applications - overvoltage category OV2; pollution degree PD2; rated surge voltage UNi = 0.5 kV; UNm = 24 V DC	Yes; Railway applications - overvoltage category OV2; pollution degree PD2; rated surge voltage UNi = 0.5 kV; UNm = 24 V DC
  ● EN 50125-1		Yes; Rail vehicles - see ambient conditions	Yes; Rail vehicles - see ambient conditions
  ● EN 50125-2		Yes; Stationary electrical equipment - see ambient conditions	Yes; Stationary electrical equipment - see ambient conditions
  ● EN 50125-3		Yes; Signal and telecommunications systems - see ambient conditions; vibrations and shocks: Application point outside of tracks (1 m to 3 m away from track)	Yes; Signal and telecommunications systems - see ambient conditions; vibrations and shocks: Application point outside of tracks (1 m to 3 m away from track)
  ● EN 50155		Yes; Rail vehicles - temperature class T1, horizontal mounting position, salt spray Class ST2	Yes; Rail vehicles - temperature class T1, horizontal mounting position, salt spray Class ST2
  ● EN 61373		Yes; Rail vehicles - vibrations and shocks: Category 1 Class A/B	Yes; Rail vehicles - vibrations and shocks: Category 1 Class A/B
  ● Fire protection acc. to EN 45545-2		Yes; Rail vehicles - verification on request	Yes; Rail vehicles - verification on request
  Ambient conditions
  Ambient temperature during operation
  ● horizontal installation, min.		-40 °C; = Tmin; Startup @ -25 °C	-40 °C; = Tmin; Startup @ -25 °C
  ● horizontal installation, max.		70 °C; = Tmax; > +60 °C max. 4x ±20 mA or 4x ±10 V permissible	70 °C; = Tmax; > +60 °C max. 2x ±20 mA or 4x ±10 V or 4x RTD permissible
  Extended ambient conditions
  ● relative to ambient temperature-atmospheric pressure-installation altitude		Tmin ... Tmax at 1080 hPa ... 795 hPa (-1000 m ... +2000 m)	Tmin ... Tmax at 1080 hPa ... 795 hPa (-1000 m ... +2000 m)
  Relative humidity
  — With condensation, tested in accordance with IEC 60068-2-38, max.		100 %; RH incl. condensation/frost (no commissioning under condensation conditions)	100 %; RH incl. condensation/frost (no commissioning under condensation conditions)
  Resistance
  — against biologically active substances / conformity with EN 60721-3-3		Yes; Class 3B2 mold, fungus and dry rot spores (with the exception of fauna). The supplied connector covers must remain on the unused interfaces during operation!	Yes; Class 3B2 mold, fungus and dry rot spores (with the exception of fauna). The supplied connector covers must remain on the unused interfaces during operation!
  — against biologically active substances/conformity with EN 60721-3-5		Yes; Class 5B2 mold and fungal spores (excluding fauna). The supplied plug covers must remain in place over the unused interfaces during operation!	Yes; Class 5B2 mold and fungal spores (excluding fauna). The supplied plug covers must remain in place over the unused interfaces during operation!
  — against chemically active substances / conformity with EN 60721-3-3		Yes; Class 3C4 (RH < 75%) incl. salt spray according to EN 60068-2-52 (degree of severity 3). The supplied connector covers must remain on the unused interfaces during operation!	Yes; Class 3C4 (RH < 75%) incl. salt spray according to EN 60068-2-52 (degree of severity 3). The supplied connector covers must remain on the unused interfaces during operation!
  — against chemically active substances/conformity with EN 60721-3-5		Yes; Class 5C3 (RH < 75%) including salt spray according to EN 50155 (ST2). The supplied plug covers must remain in place over the unused interfaces during operation!	Yes; Class 5C3 (RH < 75%) including salt spray according to EN 50155 (ST2). The supplied plug covers must remain in place over the unused interfaces during operation!
  — against mechanically active substances / conformity with EN 60721-3-3		Yes; Class 3S4 incl. sand, dust. The supplied connector covers must remain on the unused interfaces during operation!	Yes; Class 3S4 incl. sand, dust. The supplied connector covers must remain on the unused interfaces during operation!
  — against mechanically active substances/conformity with EN 60721-3-5		Yes; Class 5S3 including sand and dust. The supplied plug covers must remain in place over the unused interfaces during operation!	Yes; Class 5S3 including sand and dust. The supplied plug covers must remain in place over the unused interfaces during operation!
  Decentralized operation
  Fast Startup supported			No
  Prioritized startup		No
  Dimensions
  Width		35 mm	35 mm
  Height		147 mm	147 mm
  Depth		129 mm	129 mm
  Weights
  Weight, approx.		200 g	310 g
  Other
  Note:		For use in railway applications, also observe the product information "SIPLUS extreme RAIL" A5E37661960A Online Support article 109736776	For use in railway applications, also observe the product information "SIPLUS extreme RAIL" A5E37661960A Online Support article 109736776