Электронные модули

Заказные данные
(13)
Аксессуары
(8)

Станция ET 200iSP может комплектоваться широким спектром электронных модулей ввода-вывода дискретных и аналоговых сигналов:

8-канальный модуль ввода дискретных сигналов с поддержкой функций счета и измерения частоты.
4-канальные модули вывода дискретных сигналов.
4-канальный модуль ввода аналоговых сигналов термопар (ТС) и термопреобразователей сопротивления (RTD).
4-канальные модули ввода аналоговых сигналов с 2- и 4-проводными схемами подключения датчиков, работающие с поддержкой или без поддержки HART протокола.
4-канальный модуль вывода аналоговых сигналов, работающий с поддержкой или без поддержки HART протокола.

В комплект поставки каждого модуля 4 AI TC входит модуль внутренней температурной компенсации. Он монтируется на клеммы терминального модуля, на котором установлен электронный модуль 4 AI TC, и обеспечивает более высокую точность измерения температуры.Для модулей 4 AI, RTD рекомендуется применять внешнюю температурную компенсацию с использованием датчика температуры PT100.

Дизайн

Установка на терминальные модули TM-EM/EM60S или TM-EM/EM60C (заказываются дополнительно).
Использование функций механического кодирования для исключения ошибок при замене модулей.
“Горячая” замена модулей при работе станции в Ex-зонах.
Подключение внешних цепей через контакты терминальных модулей проводниками сечением 0.14 … 2.5 мм².
Все электронные модули могут устанавливаться в зонах EEx i и поддерживают "горячую" замену
Возможность резервирования посадочных мест для последующей установки электронных модулей с помощью ложных модулей.

Технические данные

Order number		6ES7131-7RF00-0AB0
		ET200ISP, EL-MOD., 8DI, NAMUR
Digital inputs
Number of digital inputs		8
Number of NAMUR inputs		8
Input voltage
● Type of input voltage		DC
Input delay (for rated value of input voltage)
for standard inputs
— at "0" to "1", min.		2.8 ms
— at "0" to "1", max.		3.5 ms
— at "1" to "0", min.		2.8 ms
— at "1" to "0", max.		3.5 ms
Cable length
● shielded, max.		500 m
Encoder
Number of connectable encoders, max.		8
Connectable encoders
● NAMUR encoder		Yes
NAMUR encoder
● Input current for signal "0", max.		1.2 mA
● Input current for signal "1", min.		2.1 mA
Interrupts/diagnostics/status information
Diagnostic functions		Yes
Alarms
● Diagnostic alarm		Yes; Parameterizable
● Hardware interrupt		No
Diagnostic messages
● Diagnostic information readable		Yes
● Short-circuit		Yes; R load < 150 ohms with NAMUR sensor/sensor and NAMUR changeover contact/sensor to DIN 19234
Diagnostics indication LED
● Group error SF (red)		Yes
● Status indicator digital input (green)		Yes
Integrated Functions
Frequency measurement		Yes; (Gate time) 50 ms; 200 ms; 1 s
Number of frequency meters		2
Counter
Number of counter inputs		2; normal and periodic count function
Input frequency, max.		5 kHz; with a cable length of 20 m: 5 kHz; with a cable length of 100 m: 1 kHz; with a cable length of 200 m: 500 Hz
Potential separation
Potential separation digital inputs
● between the channels		No
● between the channels and backplane bus		Yes
Permissible potential difference
between different circuits		60 V DC/30 V AC
Standards, approvals, certificates
CE mark		Yes
Use in hazardous areas
● Type of protection acc. to EN 50020 (CENELEC)		II2 G (1) GD Ex ib[ia] IIC T4 and I M2 Ex ib[ia] I
● Type of protection acc. to KEMA		04 ATEX 1248
Dimensions
Width		30 mm
Height		129 mm
Depth		136.5 mm
Weights
Weight, approx.		255 g

Order number	6ES7132-7RD01-0AB0	6ES7132-7RD11-0AB0	6ES7132-7RD22-0AB0
	ET200ISP, EL-MOD., 4DO, DC 23,1V, 20MA	ET200ISP, EL-MOD., 4DO, DC 17,4V, 27MA	ET200ISP, EL-MOD., 4DO, DC 17.4V, 40MA
Input current
from load voltage L+ (without load), max.	340 mA; with actuator supply	300 mA	400 mA
from backplane bus 3.3 V DC, max.	10 mA	10 mA
Power loss
Power loss, typ.	2.5 W	2.1 W	2.8 W
Address area
Address space per module
● without packing	2 byte	2 byte	2 byte
Digital outputs
Number of digital outputs	4; additionally 1 intrinsically-safe input for H shutdown	4; additionally 1 intrinsically-safe input for H shutdown	4; additionally 1 intrinsically-safe input for H shutdown
Short-circuit protection	Yes	Yes	Yes
No-load voltage Uao (DC)	23.1 V	17.4 V	17.4 V
Internal resistor Ri	275 Ω	150 Ω	167 Ω
Trend key points E
● Voltage Ue (DC)	17.6 V	13.3 V	10.7 V
● Current Ie	20 mA	27 mA	40 mA; 80 mA when outputs connected in parallel
Output current
● for signal "1" rated value	0.02 A	0.027 A	0.04 A
Output delay with resistive load
● "0" to "1", max.	2 ms	2 ms	2 ms
● "1" to "0", max.	1.5 ms	1.5 ms	1.5 ms
Parallel switching of two outputs
● for uprating	No; for Ex reasons not possible; nor for predecessor	Yes	Yes
Switching frequency
● with resistive load, max.	100 Hz	100 Hz	100 Hz
● with inductive load, max.	2 Hz	2 Hz	2 Hz
Cable length
● shielded, max.	500 m	500 m	500 m
● unshielded, max.	500 m	500 m	500 m
Interrupts/diagnostics/status information
Status indicator	Yes	Yes	Yes
Alarms		No
Diagnostic functions	Yes	Yes
Alarms
● Diagnostic alarm	Yes; Parameterizable	Yes; Parameterizable	Yes; Parameterizable
Diagnostic messages
● Diagnostic information readable	Yes	Yes	Yes
● Wire-break	Yes; R > 10 kohms, I < 100 µA	Yes	Yes; R > 10 kohms, I < 100 µA
● Short-circuit	Yes; R< 800 ohms (one output), R< 40 ohms (outputs connected in parallel)	Yes	Yes; R< 80 Ohm (one output), R< 40 Ohm (outputs connected in parallel)
Diagnostics indication LED
● Group error SF (red)	Yes	Yes	Yes
● Status indicator digital output (green)	Yes	Yes	Yes; Per channel
Parameter
Remark		14 byte
Diagnostics wire break	Yes	Yes	Yes
Diagnostics short-circuit	Yes	Yes	Yes
Response to CPU/master STOP	Substitute a value/keep last value	Substitute a value/keep last value	Substitute a value/keep last value
Ex(i) characteristics
Maximum values of output circuits (per channel)
● Co (permissible external capacity), max.			241 nF; For IIC, 1507 nF for IIB
● Io (short-circuit current), max.			118 mA
● Lo (permissible external inductivity), max.			1.7 mH; For IIC, 10.4 mH for IIB
● Po (power of load), max.			572 mW
● Uo (output no-load voltage), max.			19.4 V
● Ta (permissible ambient temperature), max.	70 °C	70 °C
Potential separation
Potential separation digital outputs
● between the channels	No	No	No
● between the channels and backplane bus	Yes	Yes	Yes
● Between the channels and load voltage L+	Yes	Yes	Yes
Permissible potential difference
between different circuits			60 V DC/30 V AC
Standards, approvals, certificates
CE mark			Yes
Highest safety class achievable in safety mode
● SIL acc. to IEC 61508	No		No
Use in hazardous areas
● Type of protection acc. to EN 50020 (CENELEC)	II2 G (1) GD Ex ib[ia] IIC T4 and I M2 Ex ib[ia] I	II2 G (1) GD Ex ib[ia] IIC T4 and I M2 Ex ib[ia] I	II2 G (1) GD Ex ib[ia] IIC T4 and I M2 Ex ib[ia] I
● Type of protection acc. to KEMA	04 ATEX 1249	04 ATEX 1249	04 ATEX 1249
Dimensions
Width	30 mm	30 mm	30 mm
Height	129 mm	129 mm	129 mm
Depth	136.5 mm	136.5 mm	136.5 mm
Weights
Weight, approx.	255 g	255 g	255 g

Order number	6ES7132-7GD00-0AB0	6ES7132-7GD10-0AB0	6ES7132-7GD21-0AB0	6ES7132-7GD30-0AB0
	ET200ISP, EL-MOD., 4DO, DC 23,1V, 20MA	ET200ISP, EL-MOD., 4DO, DC 17,4V, 27MA	ET200ISP, EL-MOD., 4DO, DC 17,4V, 40MA	ET200ISP, EL-MOD., 4DO, DC 25.5V, 22MA
Input current
from load voltage L+ (without load), max.	340 mA; with actuator supply	300 mA; with actuator supply	400 mA	400 mA
from backplane bus 3.3 V DC, max.	10 mA	10 mA
Power loss
Power loss, typ.	2.5 W	2.1 W	2.8 W	2.8 W
Address area
Address space per module
● without packing	2 byte	2 byte	2 byte	2 byte
Digital outputs
Number of digital outputs	4; additionally 1 intrinsically-safe input for L shutdown	4; additionally 1 intrinsically-safe input for L shutdown	4; additionally 1 intrinsically-safe input for L shutdown	4; additionally 1 intrinsically-safe input for L shutdown
Short-circuit protection	Yes	Yes	Yes	Yes
No-load voltage Uao (DC)	23.1 V	17.4 V	17.4 V	25.5 V
Internal resistor Ri	275 Ω	150 Ω	167 Ω	260 Ω
Trend key points E
● Voltage Ue (DC)	17.6 V	13.3 V	10.7 V	19.8 V
● Current Ie	20 mA	27 mA; 54 mA when outputs connected in parallel	40 mA	22 mA
Output current
● for signal "1" rated value	0.02 A	0.027 A	0.04 A	0.022 A
Output delay with resistive load
● "0" to "1", max.	2 ms	2 ms	2 ms	2 ms
● "1" to "0", max.	1.5 ms	1.5 ms	1.5 ms	1.5 ms
Parallel switching of two outputs
● for uprating	No; for Ex reasons not possible; nor for predecessor	Yes	Yes	No
Switching frequency
● with resistive load, max.	100 Hz	100 Hz	100 Hz	100 Hz
● with inductive load, max.	2 Hz	2 Hz	2 Hz	2 Hz
Cable length
● shielded, max.	500 m	500 m	500 m	500 m
● unshielded, max.	500 m	500 m	500 m	500 m
Interrupts/diagnostics/status information
Status indicator	Yes	Yes	Yes	Yes
Diagnostic functions	Yes	Yes	Yes	Yes
Alarms
● Diagnostic alarm	Yes; Parameterizable	Yes; Parameterizable	Yes; Parameterizable	Yes; Parameterizable
Diagnostic messages
● Diagnostic information readable	Yes	Yes	Yes	Yes
● Wire-break	Yes; R > 10 kohms, I < 100 µA	Yes; R > 10 kohms, I < 100 µA	Yes; R > 10 kohms, I < 100 µA	Yes; R > 10 kohms, I < 100 µA
● Short-circuit	Yes; R< 80 Ohm (one output), R< 40 Ohm (outputs connected in parallel)	Yes; R< 800 ohms (one output), R< 40 ohms (outputs connected in parallel)	Yes; R< 80 Ohm (one output), R< 40 Ohm (outputs connected in parallel)	Yes; R < 80 ohms
Diagnostics indication LED
● Group error SF (red)	Yes	Yes	Yes	Yes
● Status indicator digital output (green)	Yes	Yes	Yes; Per channel	Yes; Per channel
Parameter
Remark	14 byte	14 byte
Diagnostics wire break	Yes	Yes	Yes	Yes
Diagnostics short-circuit	Yes	Yes	Yes	Yes
Response to CPU/master STOP	Substitute a value/keep last value	Substitute a value/keep last value	Substitute a value/keep last value	Substitute a value/keep last value
Ex(i) characteristics
Maximum values of output circuits (per channel)
● Co (permissible external capacity), max.			241 nF; For IIC, 1507 nF for IIB	81 nF; For IIC, 651 nF for IIB
● Io (short-circuit current), max.			118 mA	110 mA
● Lo (permissible external inductivity), max.			1.7 mH; For IIC, 10.4 mH for IIB	1.7 mH; For IIC, 11.5 mH for IIB
● Po (power of load), max.			572 mW	764 mW
● Uo (output no-load voltage), max.			19.4 V	27.9 V
● Ta (permissible ambient temperature), max.	70 °C	70 °C
Potential separation
Potential separation digital outputs
● between the channels	No	No	No	No
● between the channels and backplane bus	Yes	Yes	Yes	Yes
● Between the channels and load voltage L+	Yes	Yes	Yes	Yes
Permissible potential difference
between different circuits			60 V DC/30 V AC	60 V DC/30 V AC
Standards, approvals, certificates
CE mark	Yes	Yes	Yes	Yes
Highest safety class achievable in safety mode
● SIL acc. to IEC 61508	No	No	No	No
Use in hazardous areas
● Type of protection acc. to EN 50020 (CENELEC)	II2 G (1) GD Ex ib[ia] IIC T4 and I M2 Ex ib[ia] I	II2 G (1) GD Ex ib[ia] IIC T4 and I M2 Ex ib[ia] I	II 2 G (1) GD and I M2 Ex ib[ia][iaD] IIC T4; Ex ib [ia] I	II 2 G (1) GD and I M2 Ex ib[ia][iaD] IIC T4; Ex ib [ia] I
● Type of protection acc. to KEMA	04 ATEX 1249	04 ATEX 1249	04 ATEX 1249	04 ATEX 1249
Dimensions
Width	30 mm	30 mm	30 mm	30 mm
Height	129 mm	129 mm	129 mm	129 mm
Depth	136.5 mm	136.5 mm	136.5 mm	136.5 mm
Weights
Weight, approx.	255 g	255 g	255 g	255 g

Order number		6ES7132-7HB00-0AB0
		ET200ISP, RELAY-MOD., 2DO, UC60V, 2A
Input current
from load voltage L+ (without load), max.		120 mA
Power loss
Power loss, typ.		1.1 W
Digital outputs
Number of digital outputs		2
Short-circuit protection		No
Output current
● for signal "1" rated value		2 A
Output delay with resistive load
● "0" to "1", max.		8 ms
● "1" to "0", max.		3 ms
Parallel switching of two outputs
● for uprating		No
● for redundant control of a load		No
Switching frequency
● with resistive load, max.		0.5 Hz; See data in manual
● with inductive load, max.		0.2 Hz; See data in manual
Relay outputs
Switching capacity of contacts
— with resistive load, up to 60 °C, max.		2 A; See data in manual
— Thermal continuous current, max.		2 A; See data in manual
Cable length
● shielded, max.		500 m
● unshielded, max.		500 m
Interrupts/diagnostics/status information
Status indicator		Yes
Alarms		No
Substitute values connectable		Yes
Alarms
● Diagnostic alarm		Yes
● Hardware interrupt		No
Diagnostic messages
● Diagnostic information readable		Yes
● Wire-break		No; Cannot be determined in contact power circuit
● Short-circuit		No; Cannot be determined in contact power circuit
Diagnostics indication LED
● Group error SF (red)		Yes
● Status indicator digital output (green)		Yes; Per channel
Ex(i) characteristics
Maximum values of output circuits (per channel)
● Uo (output no-load voltage), max.		60 V
● Um (fault voltage), max.		250 V
● Ta (permissible ambient temperature), max.		70 °C
Potential separation
Potential separation digital outputs
● between the channels		Yes
● between the channels and backplane bus		Yes
● Between the channels and load voltage L+		Yes; Channels and power bus
Standards, approvals, certificates
CE mark		Yes
Highest safety class achievable in safety mode
● SIL acc. to IEC 61508		No
Use in hazardous areas
● Type of protection acc. to EN 50020 (CENELEC)		II 2 G and I M2 Ex eibmb IIC T4; Ex eibmb I
● Type of protection acc. to KEMA		07 ATEX 0180
Dimensions
Width		30 mm
Height		129 mm
Depth		136.5 mm
Weights
Weight, approx.		255 g

Order number	6ES7193-7CA00-0AA0	6ES7193-7CA10-0AA0	6ES7193-7CA20-0AA0	6ES7193-7CB00-0AA0
	ET200ISP, TERM.-MOD. TM-EM/EM60S F. EM	ET200ISP, TERM.-MOD. TM-EM/EM60C F. EM	ET200ISP, TERM.-MOD. TM-EM/EM60S F. EM	ET200ISP, TERM.-MOD. TM-RM/RM
Standards, approvals, certificates
CE mark	Yes	Yes	Yes	Yes
Use in hazardous areas
● Type of protection acc. to EN 50020 (CENELEC)	see ET200iSP system	see ET200iSP system	No	see ET200iSP system
● Test number KEMA	04 ATEX 2242	04 ATEX 2242		07 ATEX 0205
Dimensions
Width	60 mm	60 mm	60 mm	60 mm
Height	190 mm	190 mm	190 mm	190 mm
Depth	52 mm	52 mm	52 mm	52 mm
Weights
Weight, approx.	275 g	275 g	235 g	340 g

Order number		6ES7138-7AA00-0AA0
		ET200ISP, RESERVE MODULE
Digital inputs
Number of digital inputs		0
Standards, approvals, certificates
CE mark		Yes
Use in hazardous areas
● Type of protection acc. to EN 50020 (CENELEC)		II2 G EEx ib IIC T4
● Test number KEMA		04 ATEX 1251
Dimensions
Width		30 mm
Height		129 mm
Depth		136.5 mm
Weights
Weight, approx.		180 g

Электронные модули

Информационные материалы

Дизайн

Технические данные